(0: off, 1: on)ĪT+RX2FQ: Get or Set the Rx2 window frequencyĪT+RX2DR: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)ĪT+RX1DL: Get or Set the delay between the end of the Tx and the Rx Window 1 in msĪT+RX2DL: Get or Set the delay between the end of the Tx and the Rx Window 2 in msĪT+JN1DL: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in msĪT+JN2DL: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in msĪT+NJM: Get or Set the Network Join Mode. (0-7 corresponding to DR_X)ĪT+DCS: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testingĪT+PNM: Get or Set the public network mode. (0: off, 1: on)ĪT+TXP: Get or Set the Transmit Power (0-5, MAX:0, MIN:5, according to LoRaWAN Spec)ĪT+DR: Get or Set the Data Rate. In this mode, the temperature resolution of ds18b20 is 0.25℃ to save power consumptionĪT+FDR: Reset Parameters to Factory Default, Keys ReserveĪT+APPKEY: Get or Set the Application KeyĪT+NWKSKEY: Get or Set the Network Session KeyĪT+APPSKEY: Get or Set the Application Session KeyĪT+APPEUI: Get or Set the Application EUIĪT+ADR: Get or Set the Adaptive Data Rate setting. Note: This uplink will automatically select the appropriate DR according to the data length If alarm is enabled, a data will be sent immediately if temperate exceeds the Alarm range. parameter7: 1 to enable temperature alarm, 0 to disable the temperature alarm.parameter5 & parameter6:Temperature alarm range is -16 to 32☌,.(max value is 60, means max 60 sampling in one uplink) parameter4:When there is 20 sampling dats, Device will send these data via one uplink.parameter2: Set the temperature sampling mode to 1(1:DS18B20 2:TMP117 3: Internal GXHT30).Sampling multiple times and uplink together 6.8 Why can't I see the datalog information.6.7 How to use USB-TYPE-C to connect PC to upgrade firmware?.6.6 Using USB-TYPE-C to connect to the computer using the AT command.6.5 How to use TTL-USB to connect PC to upgrade firmware?.6.4 How to use TTL-USB to connect a PC to input AT commands?.6.2 Where to use AT commands and Downlink commands.4.14 Modified WMOD command for external sensor TMP117 or DS18B20 temperature alarm(Since firmware 1.3.0).4.3 Enable/Disable uplink Temperature probe ID.Configure LHT65N via AT command or LoRaWAN downlink 2.7.2 ALARM MODE ( Before v1.3.1 firmware).2.7.1 ALARM MODE ( Since v1.3.1 firmware).2.7 Alarm Mode & Feature "Multi sampling, one uplink".2.4.6.6 Ext=8 Counting Mode(Since Firmware v1.3).2.4.6.5 Ext=4 Interrupt Mode (Since Firmware v1.3) This wiki is intended to help identify radio signals through example sounds and.2.4.6.3 Ext=6, ADC Sensor (use with E2 Cable).2.4.6.2 Ext=9, E3 sensor with Unix Timestamp.2.3.2 Step 2: Activate LHT65N by pressing the ACT button for more than 5 seconds.LTE eNodeB selects suitable modulation type based on adaptation algorithm. For LTE PDSCH channel uses QPSK, 16QAM, 64QAM modulation types. Every connection usually will have its own set of SRB. Signalling Radio Bearers (SRB) will use PDSCH. 1.1 What is LHT65N Temperature & Humidity Sensor Downlink RRC Signalling messages-These are carried by PDSCH.Dual ToR Mux Cable Configuration (optional)īy default, the active and standby ToRs for each port will be automatically determined at startup. For example the interface Ethernet0 has port number 1. If you want to know the port number of one interface, normally you can find it in the 'Alias' column. Interface Lanes Speed MTU Alias Oper Admin
0 Comments
Leave a Reply. |